50k~1000MHz 4.3'' NanoVNA HF VHF UHF Vector Network Antenna Analyzer SMA 50Ohm

Description

Description:
Features:
NanoVNA-F Mini Vector Network Analyser is a product based on the Open Source Project of NanoVNA. The RF part is consistent with the original version (NanoVNA-F uses harmonic spread measurement frequency to 1 GHz).
NanoVNA-F hardware functions include and are not limited to the following improvements:
1. Use 4.3-inch IPS TFT LCD screen, with a larger view angle and can be seen clearly in strong outdoor light.
2. Switch to large capacity 5000mAh lithium battery, standby time is longer, and expand a USB interface. Usually, it can be used as a rechargeable treasure when the instrument is not used.
3. The IC is charged by high current 2A, and the charging time is shorter.
4. Change to larger and better operating wave wheel.
5. Switch to a power switch with a greater sense of operation and a better sense of operation.
6. Support Chinese and English menu switching;
7. Upgrade the user program by virtual U disk.
8. Standard aluminium shell to protect SMA head and reduce the interference of external electromagnetic wave to instrument.
8. Software open source github.com/flyoob/NanoVNA-F
Calibration Kit:
Material: Stainless steel
Frequency: DC-6GHz, the standard load full-band standing wave is lower than 1,025.
A set of NanoVNA vector network analyzer calibration kits, including SMA open, SMA short, a 50Ω standard load, and the interface is SMA male (female thread).
The SMA load terminal is stainless steel with a low standing wave. 50 ohm imported stainless steel load, low standing wave, DC-6 GHz (1 MHz-6 GHz), the standing wave ratio is basically around 1.02.
The hardware block diagram of NanoVNA-F is as follows
NanoVNA-F measurement range is 50k-1GHz. The harmonic spread measurement frequency of the output signal of the clock chip SI5351 is 1000MHz. At 600M-1GHz, the dynamic range of S11 is 40dB (standing wave ratio is less than 1.02). At the same time, a metal shield is designed for the RF front-end, so that the dynamic range of S21 is better than 60dB in the whole frequency band.
Specification:
Size: 14CM * 7.5CM * 2CM (length, width and height)
Measuring Frequency: 50kHz ~ 1000MHz
RF output: - 13 DBM (maximum - 9 dbm)
Frequency accuracy: < 0.5 ppm
Port SWR: < 1.1
Display: 4.3 inch IPS TFT (800x480)
USB Interface: USB Type-C Communication Mode: CDC (Serial)
Power consumption: USB 5V 200mA, built-in 5000mAh battery, theoretical life of 18 hours, maximum charging current 2A
Output capability: 5V/1A, supporting Android and Apple phones
Number of calibration points: 101
Number of scanning points: 101
Display Tracking: 4, Mark: 4, Settings Save: 5
Scanning time: about 1.9s/time (50kHz-1000MHz full frequency band)
Measurable S parameters, voltage standing wave ratio SWR, phase diagram, group delay, Smith circle diagram... ;
19.0Wh (about 5000mAh after conversion) large capacity lithium battery
Designing a metal shield for the RF front end, allowing the S21 to have a dynamic range better than 60dB over the full frequency range
power bank fuction: 5V/1A , Supporting Android and Apple Mobile
Open route length test:
NanoVNA-F S11 parameter, SWR standing wave ratio test
UV9D antenna U-band standing wave ratio measurement, starting frequency: 300M, termination frequency: 600M, standing wave minimum frequency 441.000000MHz, SWR = 1.03.
S21 insertion loss measurement, low pass, high pass, band pass filter measurement
Measuring 6.5M Ceramic Notch with NanoVNA-F
Measuring 10.7M ceramic filter using NanoVNA-F
A self-made low-pass filter was measured using the NanoVNA-F with a 3dB bandwidth of approximately 400MHz.
Performance comparison, E5071C four-port vector network vs NanoVNA-F
Note:
Please allow minor errors due to manual measurement.
Item color displayed in photos may be showing slightly different since monitors are not calibrated same.
Package Contents:
1pc of Nanovna meter
2pcs of SMA-JJ RG316 cable 20CM (NanoVNA-F is a standard SMA female connector, which is used to switch to M head and N head to better protect SMA female)
1 set of calibration parts (50Ω standard load x1, open circuit calibration piece x1, short circuit calibration piece x1, use the included calibration piece, the instrument can be calibrated to get good measurement result data)
1pc of SMA-JJ double needle
1pc of SMA elbow external screw inner hole to inner screw inner needle
1pc of Type-C data cable
Or
1pc of Calibration Kit
Payment:
We only accept
PayPal
.
PayPal
is the only online payment method we accept. Please make sure you have a valid/confirmed PayPal account prior bidding.
And please make sure that your PayPal registed address is the same with your eBay registed address.
Shipping:
It usually takes about 10-30 working days to arrive for economy shipping which not including tracking number; 7-15 working days for standard shipping which including tracking number. Transit time may be a little delayed because of the bad weather and customs inspection. If you do not receive your item within 30 working days since payment finished, please contact us immediately for further assistance.
Note: It may takes more than 30 working days to other countries such as Mexico,Brazil,Chile,Peru, because they is far away from China.
PS: We also offer faster shipping service (3-5 days to deliver), such as DHL,EMS, but buyers need to pay for the extra shipping cost. Please contact us if you need it.
Customs Declaration:
Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyer's responsibility.
Please check with your country's customs office to determine what these additional costs will be prior to bidding.
Return Policy:
If you are dissatisfied with our item or service, then please follow the good eBay practice to contact us by eBay message before leaving any feedback. We are committed to resolve all issues in a friendly and satisfactory manner.
We always reply to eBay messages within 1-2 business days. If you do not get a response from us, then please check your eBay message.
Only unused, undamaged and original condition item can be qualified for a return.
Feedback:
We strive for 100% customer satisfaction!
Positive Feedback
is very important to us. If you have any questions, please feel free to contact us instead of leaving negative feedback. We will reply your email within 24 working hours.