NanoVNA-H4 4" LCD 50K~1.5GHz VNA HF VHF UHF UV Vector Network Analyzer Hugen

Description

Welcome to my shop
Product Overview
NanoVNA-H4 4" LCD 50K~1.5GHz VNA HF VHF UHF UV Vector Network Analyzer +Battery
Detail
50KHz-1.5GHz Vector Network Analyzer NanoVNA Vector w/ 4" LCD Display For UHF Antenna NanoVNA-H4
Features:
- With DC dimming method, 4" full-view LCD screen can be seen more clearly for outdoor uses, and more comfortable for indoor uses
- Optimized Electric Bridge: Making full use of the harmonics of Si5351, it can use the 5th harmonic to measure up to 1.5GHz
- When fundamental wave is used, the output level of CH0 is increased to 0dBm, making reflection measurement more accurate
- Solved the abnormality of NanoVNA-H when operating at around 6MHz before
- Redesigned power management circuit reduces power noise, USB power interference, and charging current
- Improved PCB layout
- Reserved UART interface for DIY expansion
- Lightweight ABS shell keeps the device well protected
Basic Parameters:
- ABS Shell: 75mm x 133mm x 18mm (excluding protrusions)
- Measurement Frequency: 50KHz ~ 1.5GHz
- RF Output: 0dbm (±2dB, fundamental wave)
- Frequency Accuracy: <2ppm
- Frequency Stability: <0.5ppm
- Measurement Range: 70dB (50kHz-300 MHz), (60dB (300M-900MHz), 40dB (0.9G-1.5GHz) enable expansion firmware)
Note: Please pay attention to the error caused by nonlinear transformation of the fundamental wave when using harmonic measurement.
- Port SWR: <1.1
- Display: 4" TFT (320 x 480)
- USB Interface: USB type-C; Communication Mode: CDC (serial)
- Power Supply: USB 5V 200mA. Maximum charging current 1A
- Number of Calibration Points: 101 (fixed)
- Number of Scanning Points: 101 (fixed)
- Display Tracking: 4, Marking: 4, Save Setting: 5
- Measurement of S-parameters, voltage standing wave ratio, phase, delay, Smith chart, time domain analysis, etc.
Package Included:
- 1 x NanoVNA Main Unit
- 2 x 15cm SMA Male to Male RG316 RF Cables
- 1 x SMA Female to Female Connector
- 1 x SMA Simple Calibration Kit SHORT
- 1 x SMA Simple Calibration Kit OPEN
- 1 x SMA Simple Calibration Kit LOAD
- 1 x USB Type-C Data Cable
- 1 x Type-C to Type-C (For Android mobile phone connection)
Download Manuals & PC Control Software:
Test Short-wave Antenna:
- The yellow line pictured is the standing wave ratio.
- Note: As the SMA ports are made of cast copper, please not connect hard 50-7 / RG213 and other cables directly to the SMA ports through M-to-SMA connector to avoid damaging the SMA ports. You can use the included SMA cable to connect to the SMA port as shown in the picture below, and then use M to SMA connector.
Test UHF Antenna:
Test VHF Low-pass Filter:
Test 455K SSB Filter with Bandwidth 2.4K:
PC Software:
Computer software supports control and real-time display. And it support for exporting Touchstone (snp) files for various radio design and simulation software.
As a measuring device, accuracy is of great importance. Simple calibration parts are included in the package. We have calibrated the product's dual ports before delivery. When your measurement conditions change (for example, switching from a narrower calibration bandwidth to a wider measurement bandwidth with an extension cable measurement), you need to re-calibrate. After calibration, it is saved as setting 0, which can be used directly at the next boot, or it can be saved to the other 4 saved items through recall when needed.
The following figure is the comparison data of a V-band duplexer measured with NanoVNA and E5062A for Agilent under the same test conditions:
Shipping Policy
Item Location
Payment Mathord
Returns Policy
About Feedback
Shipping Policy
Item Location
Payment Mathord
1. PayPal payment accepted only.
2. Items will be shipped to your eBay address. Please make sure it is correct.
3. Payment must be received 4 days after auction ended.
Returns Policy
1. Customer satisfaction is our top goal. We believe our items are so outstanding. All products are quality checked. They are new and in good condition when shipped to our customers. We are convinced you will be happy with your Purchase.
2. If product is defective or damage upon arrival, or wrong product shipped, please contact us immediately. Returns accepted within 14 days of delivery date and item must be in original new condition, not worn or altered in any way with attached tags & wrap. Otherwise deal is final. Return shipping must be paid by buyer.
3. Please contact us first if you have any problems/questions/concerns. We will be happy to resolve any issues you may have in a cordial and friendly manner.
4. We appreciate your Postive Feedback, and will do the same in return. DO NOT leave negative feedback without first communication with us. Please allow max 2 business days for us to response.
About Feedback
When you satisfied with our product and services please leave us positive feedback.
If a problem occurs, contact us immediately with any email request. Just contact us using the " Ask the seller a question" link on eBay.